Log InSign Up

Top 12 Bike Mechanic Skills to Put on Your Resume

In the competitive world of bicycle mechanics, standing out to potential employers requires showcasing a diverse set of skills on your resume. Highlighting the top skills not only demonstrates your expertise and versatility in bike repair and maintenance but also positions you as a valuable candidate for any bike shop or cycling team.

Top 12 Bike Mechanic Skills to Put on Your Resume

Bike Mechanic Skills

  1. Wheel Truing
  2. Hydraulic Braking
  3. Derailleur Adjustment
  4. Suspension Tuning
  5. Shimano Di2
  6. SRAM AXS
  7. Campagnolo EPS
  8. Tubeless Setup
  9. Carbon Repair
  10. Electronic Shifting
  11. Bearing Overhaul
  12. Spoke Replacement

1. Wheel Truing

Wheel truing is the process of adjusting the tension of the spokes on a bicycle wheel to ensure it is straight and runs true, eliminating wobbles or misalignments.

Why It's Important

Wheel truing is important because it ensures that a bicycle wheel is straight, round, and properly tensioned, leading to safer, more efficient riding and prolonging the wheel's lifespan.

How to Improve Wheel Truing Skills

Improving wheel truing involves precision and patience. Here are concise steps for a bike mechanic to enhance their wheel truing skills:

  1. Inspect the Wheel: Check for any obvious damages or dents. Ensure the wheel is securely mounted on the truing stand.

  2. Adjust Tension: Use a spoke wrench to adjust spoke tension. Tighten or loosen spokes to correct lateral (side-to-side) and radial (up-and-down) trueness. Aim for even tension throughout (Sheldon Brown's Guide).

  3. Check Dish: Ensure the wheel is centered between the locknuts. Use a dishing tool or compare the gap between the rim and brake pads on both sides when flipped in the truing stand (Park Tool Guide).

  4. Repeat: Truing is iterative. Re-check trueness and spoke tension after initial adjustments.

  5. Practice: Regular practice on different wheels will improve skills and intuition for truing.

Remember, the goal is to achieve a wheel that is straight, centered, and with even spoke tension for optimal performance and safety.

How to Display Wheel Truing Skills on Your Resume

How to Display Wheel Truing Skills on Your Resume

2. Hydraulic Braking

Hydraulic braking for bicycles involves the use of fluid (usually mineral oil or synthetic fluid) within a sealed system to transfer force from the brake lever to the brake pads. When the lever is squeezed, pressure increases in the system, pushing the pads against the rotor (disc brake) or rim (hydraulic rim brakes) to slow or stop the bike. This system offers improved braking performance and modulation compared to mechanical (cable-actuated) brakes.

Why It's Important

Hydraulic braking is crucial for bikes as it provides consistent, powerful braking performance with minimal effort, enhancing safety and control, especially in wet or demanding conditions.

How to Improve Hydraulic Braking Skills

To improve hydraulic braking on a bike, follow these concise steps:

  1. Bleed the Brake System: Remove air bubbles to ensure consistent brake performance. Park Tool provides a comprehensive guide.

  2. Replace Brake Fluid: Use the manufacturer-recommended fluid to maintain optimum braking. Shimano's brake fluid replacement procedure is a useful reference.

  3. Inspect and Replace Brake Pads: Check for wear and replace with high-quality pads. SRAM’s guide on brake pad replacement is helpful.

  4. Check and True Rotors: Ensure they are straight and not worn beyond the minimum thickness. Here's a guide by Park Tool.

  5. Adjust Brake Lever Reach and Free Stroke: Customize for comfort and efficiency. Shimano's lever adjustment guide can be applied.

  6. Regular Maintenance: Clean your braking system regularly and check for hydraulic line damage or leaks.

By adhering to these steps, you will improve your hydraulic braking system's performance and longevity.

How to Display Hydraulic Braking Skills on Your Resume

How to Display Hydraulic Braking Skills on Your Resume

3. Derailleur Adjustment

Derailleur adjustment on a bicycle involves fine-tuning the position and tension of the front and/or rear derailleur to achieve precise shifting across the gear range, ensuring the chain moves smoothly and accurately between gears without skipping or rubbing. This process typically includes setting the limit screws, adjusting cable tension, and aligning the derailleur with the sprockets.

Why It's Important

Derailleur adjustment is crucial for ensuring smooth, precise gear shifting, optimizing performance, and preventing chain skipping or dropping, which can lead to accidents or mechanical damage.

How to Improve Derailleur Adjustment Skills

Improving derailleur adjustment involves precise steps to ensure smooth shifting and optimal performance. Here are the key steps succinctly described:

  1. Check Derailleur Alignment: Ensure the derailleur hanger is straight. A hanger alignment tool can be used for accuracy.

  2. Set Limit Screws: Adjust the high (H) and low (L) limit screws to prevent the chain from shifting beyond the smallest and largest cogs. Park Tool provides a detailed guide on limit screw adjustment.

  3. Adjust Cable Tension: Shift to the smallest cog. If shifting is sluggish, increase cable tension by turning the barrel adjuster counterclockwise. For detailed steps, see this cable tension adjustment guide.

  4. Fine-tune Indexing: Shift through all gears, fine-tuning with the barrel adjuster for smooth transitions. Slight adjustments can make significant differences.

  5. B-Tension Adjustment: Adjust the B-tension screw to set the correct distance between the guide pulley and the cogs, ensuring crisp shifting. Shimano offers a clear explanation on B-tension adjustment.

Remember, patience and small adjustments are key to perfecting derailleur setup.

How to Display Derailleur Adjustment Skills on Your Resume

How to Display Derailleur Adjustment Skills on Your Resume

4. Suspension Tuning

Suspension tuning for a bike mechanic involves adjusting the bike's suspension system—comprising the front fork and rear shock—to match the rider's weight, riding style, and the terrain being ridden. This process optimizes the bike's handling, comfort, and performance by setting the correct sag, rebound, and compression damping levels.

Why It's Important

Suspension tuning is crucial for optimizing a bike's handling, comfort, and safety, ensuring it performs well under specific riding conditions and rider preferences.

How to Improve Suspension Tuning Skills

Improving suspension tuning on a bike involves optimizing the bike's shock absorbers for better performance, comfort, and handling. Here's a concise guide for a bike mechanic:

  1. Understand the Basics: Start by understanding the basic components and how they work together—springs, dampers (shock absorbers), and geometry. Suspension Theory.

  2. Set Sag Correctly: Adjust the sag (how much the suspension compresses under the rider's weight) to the recommended percentage of the total suspension travel, ensuring a balance between comfort and efficiency. Sag Setup.

  3. Adjust Damping: Fine-tune the compression and rebound damping to manage how the suspension compresses and returns after a hit. This is crucial for control and comfort. Damping Adjustment.

  4. Consider Spring Rate: For coil shocks, ensure the spring rate (stiffness) matches the rider's weight and riding style. For air shocks, this is adjusted by changing air pressure. Spring Rate Guide.

  5. Test and Refine: Every adjustment should be followed by testing in a controlled environment. Small adjustments can have a big impact. Always refine based on rider feedback. Testing Tips.

  6. Maintenance: Regular maintenance is essential for optimal performance. Keep the suspension components clean and serviced according to the manufacturer's schedule. Maintenance Basics.

These steps provide a foundation for suspension tuning. Always refer to the manufacturer's guidelines for specific settings and maintenance procedures.

How to Display Suspension Tuning Skills on Your Resume

How to Display Suspension Tuning Skills on Your Resume

5. Shimano Di2

Shimano Di2 refers to Shimano's electronic gear shifting system for bicycles, utilizing motor-driven mechanisms for precise and rapid gear changes with minimal effort.

Why It's Important

Shimano Di2 represents a significant advancement in bicycle technology, offering precise, fast, and reliable electronic shifting, reducing maintenance and adjustment needs compared to mechanical systems, thus streamlining a bike mechanic's workload and enhancing overall cycling performance.

How to Improve Shimano Di2 Skills

Improving Shimano Di2 performance involves several key steps, focusing on firmware updates, wiring checks, and component adjustments. Here’s a concise guide:

  1. Firmware Updates: Regularly update Di2 firmware using the E-Tube Project software. This ensures optimal performance and compatibility with new features.

  2. Battery Maintenance: Regularly check the battery level and ensure it’s properly charged. A low battery can affect shifting performance.

  3. Wiring Check: Inspect all electrical connections and wires for damage or loose connections. Ensure all components are securely connected.

  4. Derailleur Adjustment: Fine-tune front and rear derailleurs for precise shifting. Refer to Shimano’s Derailleur Adjustment Guide.

  5. Shift Speed Settings: Customize shift speed and operation using the E-Tube software, tailoring the performance to the rider's preference.

  6. System Check and Diagnostics: Use the E-Tube software to perform system checks and diagnostics, identifying any potential issues.

  7. Clean and Lubricate: Keep the drivetrain clean and well-lubricated for smooth operation.

  8. Professional Calibration: Consider professional calibration and alignment for optimal performance, especially after significant bike modifications or component changes.

For detailed procedures and updates, always refer to the official Shimano manuals and technical documents.

By following these steps, you can ensure that the Di2 system operates smoothly, providing the best possible riding experience.

How to Display Shimano Di2 Skills on Your Resume

How to Display Shimano Di2 Skills on Your Resume

6. SRAM AXS

SRAM AXS is a wireless electronic shifting system for bicycles, offering precise, quick gear changes with minimal effort.

Why It's Important

SRAM AXS is important because it represents the latest in wireless electronic shifting technology, offering precise, fast gear changes and customizable shifting options, reducing maintenance and eliminating cable wear and tear for bike mechanics.

How to Improve SRAM AXS Skills

Improving SRAM AXS performance on your bike involves a few key steps focused on setup, maintenance, and firmware updates. Here's a concise guide:

  1. Firmware Update: Regularly update your SRAM AXS components using the AXS Mobile App. This ensures optimal performance and access to the latest features.

  2. Proper Installation and Adjustment: Ensure that the derailleur hanger is straight and the derailleur is correctly mounted. Precise setup instructions can be found in the SRAM Support section.

  3. Battery Management: Regularly check and charge your AXS batteries. Keep contacts clean and store batteries in a cool, dry place. More tips on battery care are available on the SRAM FAQ page.

  4. Chain and Cassette Maintenance: Keep the chain and cassette clean and lubricated to ensure smooth shifting. SRAM provides maintenance tips at Chain Maintenance.

  5. Use the Right Tools: Employ specific tools recommended by SRAM for adjustments and maintenance to avoid damage. SRAM's tool recommendations are provided in their Technical Manuals.

  6. Professional Calibration: In case of persistent issues, consider a professional calibration of your AXS system at an authorized SRAM dealer. Dealer locations can be found through the SRAM Dealer Locator.

By following these steps, you can ensure your SRAM AXS system operates at its best.

How to Display SRAM AXS Skills on Your Resume

How to Display SRAM AXS Skills on Your Resume

7. Campagnolo EPS

Campagnolo EPS (Electronic Power Shift) is an electronic gear shifting system for bicycles, providing precise and quick shifts through electronic actuation of the derailleurs, powered by a rechargeable battery.

Why It's Important

Campagnolo EPS (Electronic Power Shift) is important for a bike mechanic because it represents a high-end, electronic gear shifting system that requires specific knowledge for installation, adjustment, maintenance, and troubleshooting, enabling mechanics to work on advanced cycling technology and offer specialized services to cyclists seeking precision and efficiency in gear changes.

How to Improve Campagnolo EPS Skills

Improving the performance of a Campagnolo Electronic Power Shift (EPS) system on a bicycle involves ensuring firmware is up-to-date, proper installation, and regular maintenance. Here’s a concise guide for bike mechanics:

  1. Firmware Updates: Regularly check and update the EPS system's firmware for optimal performance and compatibility. Use the MyCampy app for updates.

  2. Correct Installation: Ensure all components are correctly installed. Follow the official Campagnolo technical manual for guidance.

  3. Battery Maintenance: Regularly check the battery level and ensure it is properly charged. Refer to Campagnolo's guidelines on battery management.

  4. Clean Contacts: Clean the electronic contacts with a dry cloth to ensure good connectivity.

  5. Check Wiring: Inspect wiring for any signs of wear or damage. Replace if necessary using official Campagnolo components.

  6. Derailleur Adjustment: Fine-tune front and rear derailleurs for precise shifting. Use the EPS interface for adjustments.

  7. Lubrication: Ensure all moving parts, excluding electronic components, are lubricated according to Campagnolo specifications.

  8. Diagnostic Tool: Utilize the Campagnolo EPS V3 interface and the MyCampy app for diagnostics and troubleshooting.

Regular maintenance and firmware updates are key to keeping the Campagnolo EPS system performing at its best. Always refer to the latest Campagnolo technical documents for specific procedures and guidelines.

How to Display Campagnolo EPS Skills on Your Resume

How to Display Campagnolo EPS Skills on Your Resume

8. Tubeless Setup

A tubeless setup on a bicycle eliminates inner tubes from the tires, using a sealed rim and a tire with a liquid sealant inside to prevent and repair punctures, providing a lighter setup and improved ride quality due to lower tire pressures without the risk of pinch flats.

Why It's Important

Tubeless setups eliminate the need for an inner tube, reducing the risk of punctures and allowing for lower tire pressures, which enhances traction and ride comfort. It's crucial for bike mechanics to master for improved reliability and performance of bikes.

How to Improve Tubeless Setup Skills

Improving a tubeless setup on a bicycle can greatly enhance performance and reduce the likelihood of flats. Here are concise steps to optimize a tubeless system:

  1. Inspect and Prepare the Rim: Ensure the rim is clean and free from damage. Rim Tape Application Guide.

  2. Choose the Right Tape: Select a tubeless tape that matches the inner width of your rim for a secure fit. Tubeless Tape Selection.

  3. Apply Tubeless Tape Properly: Stretch the tape tightly around the rim in an overlapping fashion to ensure an airtight seal. Tape Application Technique.

  4. Install the Valve: Insert a tubeless valve through the rim tape, ensuring it's tight and sealed. Valve Installation.

  5. Seat the Tire Correctly: Place the tire onto the rim, making sure it sits evenly before inflation. Lubricate the tire bead with soapy water for easier seating. Tire Seating Tips.

  6. Inflate and Seal: Use a compressor or a tubeless pump to quickly inflate the tire, ensuring the bead seats properly against the rim. Add sealant through the valve or before the final tire bead is in place. Sealant Guide.

  7. Check for Leaks: Spray soapy water around the rim and valve to check for air bubbles indicating leaks. Adjust as necessary. Leak Detection.

  8. Maintain Proper Pressure: Regularly check and maintain tire pressure to suit riding conditions and preferences. Pressure Guide.

Remember, a well-executed tubeless setup can offer significant benefits in terms of performance and puncture resistance.

How to Display Tubeless Setup Skills on Your Resume

How to Display Tubeless Setup Skills on Your Resume

9. Carbon Repair

Carbon Repair, in the context of a bike mechanic, refers to the process of fixing damages such as cracks, dents, or fractures on carbon fiber bicycle components, typically using materials like carbon fiber cloth and resin to restore integrity and functionality.

Why It's Important

Carbon repair is crucial for maintaining the structural integrity and safety of carbon fiber bicycle components, ensuring optimal performance and prolonging their lifespan.

How to Improve Carbon Repair Skills

Improving carbon repair, especially for bike mechanics, involves a few key steps focusing on accuracy, safety, and aesthetics. Here's a concise guide:

  1. Assessment: Carefully inspect the damage. Use a magnifying glass or microscope for micro-cracks. Park Tool offers detailed guidelines on assessing bike damage.

  2. Preparation: Clean the area thoroughly with isopropyl alcohol. Sand the damaged area gently to remove any loose fibers. Mask off surrounding areas to protect them.

  3. Materials: Use high-quality carbon fiber fabric and epoxy resin. Choose materials that match the bike frame's properties. Composites World provides insights into selecting the right materials.

  4. Application: Apply the epoxy resin to the carbon fabric, ensuring it's fully saturated. Place the fabric over the damaged area, using a brush to smooth out any air bubbles. Layering might be necessary for deeper repairs.

  5. Curing: Follow the epoxy manufacturer's instructions for curing time and conditions. A heat lamp can improve curing. Ensure the area is well-ventilated.

  6. Finishing: Once cured, sand the repaired area to match the frame's shape. Start with coarse sandpaper and finish with fine grit for a smooth surface.

  7. Painting: Match the paint to the original frame color. ColorRite offers a wide selection of colors. Apply primer, color, and clear coat, allowing adequate drying time between layers.

  8. Inspection and Testing: Carefully inspect the repair and the surrounding areas for any signs of weakness or imperfection. Test the repair under controlled conditions to ensure safety.

For further learning on bike mechanics and repair techniques, consider visiting Sheldon Brown's Bicycle Technical Info and the International Bike Fitting Institute for comprehensive resources and guides.

How to Display Carbon Repair Skills on Your Resume

How to Display Carbon Repair Skills on Your Resume

10. Electronic Shifting

Electronic shifting refers to a bicycle gear-changing system that uses electric motors to shift gears instead of traditional mechanical cables and levers. This system offers precise, quick, and consistent gear changes with the push of a button.

Why It's Important

Electronic shifting provides precise, swift gear changes with minimal effort, enhancing ride quality and reducing maintenance, important for ensuring optimal performance and customer satisfaction.

How to Improve Electronic Shifting Skills

To improve electronic shifting on a bicycle, follow these concise steps:

  1. Update Firmware: Ensure the shifting system's firmware is up-to-date for optimal performance. Manufacturers often release updates that can be applied using their specific app or software.

  2. Check Battery Level: Regularly check and maintain the charge of the electronic shifting system's battery. A low battery can affect shifting performance.

  3. Clean Contacts: Clean all electronic contacts with a contact cleaner to ensure good connectivity. Dirt and grime can interfere with signal transmission.

  4. Adjust Derailleur Alignment: Properly align the front and rear derailleurs according to the manufacturer's specifications. Misalignment can cause inaccurate shifting.

  5. Calibrate the System: Follow the manufacturer’s procedure to calibrate the shifting system. This often involves setting the correct gear positions and limits through a specific app or device interface.

  6. Inspect Wiring: Check all wiring for damage or wear. Replace any damaged wires to prevent signal loss or intermittent operation.

  7. Lubricate Moving Parts: Ensure that all moving parts of the derailleur are lubricated and moving freely. Stiff links or pivots can hinder shifting performance.

  8. Professional Training: Consider manufacturer-specific training courses to stay updated on the latest electronic shifting technologies and troubleshooting methods.

For more in-depth information and resources, visit manufacturer websites:

How to Display Electronic Shifting Skills on Your Resume

How to Display Electronic Shifting Skills on Your Resume

11. Bearing Overhaul

A bearing overhaul for a bike mechanic involves disassembling, cleaning, inspecting, and possibly replacing the bearings within the bike's components (such as the wheel hubs, bottom bracket, or headset) to ensure smooth rotation and extend the component's lifespan. Lubrication is also reapplied during reassembly.

Why It's Important

Bearing overhaul is crucial for a bike mechanic because it ensures the smooth operation of moving parts, reduces friction and wear, prolongs component life, and enhances ride quality and performance.

How to Improve Bearing Overhaul Skills

To improve a bike's bearing overhaul, follow these concise steps:

  1. Cleanliness: Start with a clean workspace and clean bike parts. Use a degreaser to remove old grease and debris from the bearings and bearing races.

  2. Inspection: Examine the bearings and races for wear or damage. Replace any components that show significant wear or damage. Sheldon Brown's guide on hubs provides insight into what to look for.

  3. Selection of Grease: Use high-quality, bike-specific grease. The right grease reduces friction and protects against wear and corrosion. Park Tool offers options designed for bicycle bearings.

  4. Proper Installation: Follow the manufacturer's guidelines for installing bearings and adjusting preload. Over-tightening can cause premature wear, while too loose of a fit can lead to play in the bearing. This guide from Park Tool can help with hub adjustment.

  5. Tool Use: Use the correct tools for bearing removal and installation to avoid damaging the bearings or bike. Park Tool's bearing tools section provides a comprehensive list of necessary tools.

  6. Testing: After reassembly, test the bike for smooth operation. Spin the wheels and pedals to feel for any roughness or play, which could indicate incorrect installation or the need for further adjustment.

By following these steps and continually educating yourself through reliable sources, you can ensure a high-quality bearing overhaul.

How to Display Bearing Overhaul Skills on Your Resume

How to Display Bearing Overhaul Skills on Your Resume

12. Spoke Replacement

Spoke replacement involves removing a damaged or broken spoke from a bicycle wheel, then installing and tensioning a new spoke to ensure the wheel remains true and functional.

Why It's Important

Spoke replacement is crucial for maintaining wheel integrity, ensuring proper alignment and balance, and preventing further damage or failure during rides, essential for rider safety and optimal bike performance.

How to Improve Spoke Replacement Skills

Improving spoke replacement involves precision and the right technique. Here are concise steps and resources:

  1. Identify the Broken Spoke: Inspect the wheel for the broken or bent spoke.

  2. Remove the Damaged Spoke: Loosen the nipple with a spoke wrench and remove the spoke from the hub.

  3. Insert the New Spoke: Thread the new spoke through the hub and into the rim in the correct pattern.

  4. Tension the Spoke: Tighten the nipple so that the spoke has similar tension to others. Use a spoke tension meter for accuracy.

  5. True the Wheel: Adjust the tension of spokes around the new one to ensure the wheel is straight. Spin the wheel to check for wobbles and adjust as needed.

  6. Final Check: Ensure all spokes are properly tensioned and the wheel is true. Check the wheel in the bike frame for any issues.

For detailed instructions and visual aids, consider these resources:

Remember, practice and patience are key to mastering spoke replacement.

How to Display Spoke Replacement Skills on Your Resume

How to Display Spoke Replacement Skills on Your Resume